I-Track Car Motion díly pro stavbu silnic

New

Mounting struts No.3 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

6,67€

DETAIL

FLEXI transition pieces 1.35/2,85 × 10 cm 12 pcs

IN STOCK

Transition piece. For curves with a radius of less than 20 cm, use the FLEXI transition piece HCT9403T and continue with FLEXI segments 2,85 cm HCT9402F. This increases the spacing of the guide magnetic strips to 1 cm, allowing longer vehicles and buses to pass each other safely in curves. At the end of the curve, use the same transition piece again to return to the standard spacing of the guide magnetic strips of 4 cm on straight sections.

5,90€

DETAIL

New

Mounting struts No.14 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

9,71€

DETAIL

New

Road bedding plates 90° intersection CarMotion

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

8,46€

DETAIL

New

Road bedding plates 60° intersection Right

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

7,33€

DETAIL

New

Road bedding plates 60° intersection Left

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

7,33€

DETAIL

New

Intelligent ring–undermount installation charger L

IN STOCK

Practical Intelligent ring for underfloor installation of the CarMotion Inductive Charger (L). Simply and quickly screw it to the underside of the base plate. Align the charger with the top side of the plate and secure it at the required height by tightening a single screw. If necessary, just loosen three screws – the device can be removed immediately without having to damage the road surface.

8,88€

DETAIL

New

Intelligent branch mounting ring, under-mount W

IN STOCK

Practical holder for underfloor installation of the CarMotion Switch W. Simply and quickly screw it to the underside of the base plate. Align the Switch with the top side of the plate and secure it at the required height by tightening a single screw. If necessary, just loosen three screws – the device can be removed immediately without having to damage the road surface.

8,88€

DETAIL

New

Reduction between diameters of 21 and 22.5 cm

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

5,33€

DETAIL

New

Street bedding Straight element for CarMotion

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

8,00€

DETAIL

New

Street bedding curved element 30° for CarMotion

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

11,08€

DETAIL

New

Street bedding curved element 45° for CarMotion

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

11,96€

DETAIL

I-Track Car Motion Road construction parts