VIESSMANN Car Motion příslušenství

H0 retrofit kit steered rear axles for semi-traile

check availability

These steered axles for semi-trailers are ideal for driving even with longer trailers on tighter radii, without having to widen the road significantly in curves or causing the trailers to stray too far into the lane of oncoming traffic. Precisely guided by a ball-bearing gear-ring mechanism.

44,58€

DETAIL

New

H0 Retrofit Kit Rubber Tires for Kibri Trailers an

IN STOCK

Product Information "H0 Retrofit Kit Rubber Tires for Kibri Trailers and Semi-Trailers, Twin Tires" This kit allows you to retrofit your Kibri trailers or semi-trailers to optimize the smooth running and tracking of the vehicle. This improves the handling characteristics of the trailer or semi-trailer. Contents: 8 rubber tires, 4 rims, 2 steel axles, 4 bushings. Suitable for 2-axle trailers and semi-trailers with twin tires.

25,83€

DETAIL

8421 H0 front axle complete

check availability

Front axle fully assembled with steering arm and magnet for CarMotion trucks. L 1.5 x W 2.8 x H 1.3 cm

18,46€

DETAIL

New

Mounting struts No.10 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

8,92€

DETAIL

New

Mounting struts No.16 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

10,04€

DETAIL

New

Charger for trucks and buses

IN STOCK

The charger for trucks and buses in the Viessmann CarMotion system can be powered by any standard USB power adapter or virtually any device such as a PC, laptop, power bank, etc. The charger can be connected to a USB-A power source using the included cable. The charger plug is simply inserted into the designated socket under the CarMotion vehicle. An empty battery is charged in approximately 35 minutes, and a partially discharged battery is charged correspondingly faster. The current charging status of the vehicle is indicated during charging by the vehicle's interior lighting flashing in four different levels.

26,79€

DETAIL

Inductive Charger

check availability

The InductiveCharger enables wireless vehicle recharging and inductive communication with the vehicle. Vehicles stop on the module and automatically position themselves over the charging coil, with charging currents being automatically adjusted. These modules are particularly suitable for locations with longer stop times, such as traffic lights, railroad crossings, or gas stations. Multiple modules can be networked with future software updates to autonomously guide vehicles to charging positions. A control output for the motorized 2/3-way junction (item 8448), which can also control servos, rounds out the capabilities. For trucks, the ratio of travel time to charging time is approximately 3:1. This allows for virtually unlimited travel time. The InductiveCharger can also switch vehicles with receiver coils on and off. The vehicles must be retrofitted with the receiver coil (item 8440). Charging coil diameter: 40 mm, electronics diameter: 30 mm, height: 60 mm

137,29€

DETAIL

Permanent magnet holder for test operation, 2 piec

check availability

The permanent magnet mount is the ideal solution for testing the CarMotion system. Equipped with one or more magnets, the mount can be flexibly positioned to the right of the road. This allows you to specifically test whether and where the CarMotion vehicle recognizes and implements defined control commands. The robust design allows for quick setup and easy repositioning during test runs – for precise results under realistic conditions.The permanent magnet mount is the ideal solution for testing the CarMotion system. Equipped with one or more magnets, the mount can be flexibly positioned to the right of the road. This allows you to specifically test whether and where the CarMotion vehicle recognizes and implements defined control commands. The robust design allows for quick setup and easy repositioning during test runs – for precise results under realistic conditions.

6,67€

DETAIL

8230 H0 MB ACTROS 2-axle concrete mixer trailer

IN STOCK

This practical accessory set contains a remote control, 10 meters of magnetic tape (0.5 mm), 10 permanent magnets, a charger and a programming device.

102,96€

DETAIL

New

Mounting struts No.11 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

9,12€

DETAIL

New

Mounting struts No.13 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

9,50€

DETAIL

8426 H0 gearbox with motor

check availability

Powerful, low-wear motor for underfloor drive with an encapsulated gearbox and one driven axle, suitable for CarMotion vehicles. The rear axle is non-driven and height-adjustable. Operating voltage: 7–12 V DC L 4 x W 2.8 x H 1.3 cm

41,29€

DETAIL

VIESSMANN Car Motion Accessories