VIESSMANN Car Motion příslušenství

Receiver coil for retrofitting trucks and buses

check availability

The receiver coil adds inductive charging and the necessary communication capabilities to vehicles. It simply clips onto the transmission block and connects to the vehicle's circuit board via a two-pin connector. Combined with the Inductive Charger (item 8408), it enables unlimited driving time without user intervention. Vehicles can be switched on and off at inductive charging stations. The driving time-to-charging time ratio is approximately 3:1, depending on the system and vehicle conditions. Suitable for all CarMotion system vehicles without built-in receiver coils. External dimensions: L 2.4 x W 1.3 x H 0.27 cm

10,75€

DETAIL

New

Mounting struts No.1-18 for CarMotion, 18+18 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

18,00€

DETAIL

Universal electronics truck

check availability

The Universal Electronics Truck offers compact solutions for retrofitting trucks (over 7.5 t) with the proven driving characteristics of CarMotion trucks. The slim module (W 12.5 mm x L 26.5 mm) is particularly suitable for tight installation situations and works in conjunction with the H0 gearbox with motor (item no. 8426). Power is supplied by two 60 mAh batteries included in the set. The module is intended exclusively for this motor and batteries. An additional, shortenable distribution board (approx. W 7 mm x L 25 mm; shortenable to L 17 mm) facilitates the connection of LEDs for lighting tasks and enables additional lighting effects. An expansion interface for additional modules is available. The LEDs and sensors are already provided with enameled wires to ensure easy installation. Additional sets for additional lighting effects will be available in the future. The set includes: main board, distribution board, hall sensor, charging and programming socket, 2 batteries, rear bumper

102,42€

DETAIL

New

8430 Magnetic tape 1 mm, 5 m

IN STOCK

The self-adhesive magnetic tape has a polarized surface (south pole facing up). It guides the guide magnets of the CarMotion vehicles. Depending on the type of road, it is inserted into a prefabricated road system or installed into the system plate using a surface milling machine. Dimensions: L 500 x W 0.3 x H 0.1 cm.

18,92€

DETAIL

New

Mounting struts No.7 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

7,50€

DETAIL

New

Mounting struts No.15 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

9,83€

DETAIL

New

Straight connecting segment 11 x 12 cm

IN STOCK

I-Track segments are designed for easy construction of elevated roads, bridges and smooth height transitions within the Car Motion system. They enable fast and precise creation of a stable road infrastructure. The segments are made of high-quality plywood and are supplied as a kit. Straight and curved versions are available, with curved segments configurable for left- or right-hand curves. The individual parts are easily assembled using CA Hacker superglue or wood glue, without the need for cutting or sanding. Thanks to their well-designed construction, the segments are strong and resistant to bending. The height and gradient of the roads can be easily adjusted using I-Track struts. The dimensions of the segments correspond to common CarMotion systems, ensuring easy compatibility and seamless integration into existing layouts.

8,21€

DETAIL

H0 Set of rubber tires, 10 pieces

IN STOCK

This set allows you to equip your CarMotion trucks if the original tires are damaged or worn out. The tires are characterized by good traction, smooth running, and directional stability, and can also be used for truck trailers.

9,75€

DETAIL

New

Mounting struts No.8 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

8,50€

DETAIL

New

Mounting struts No.17 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

10,25€

DETAIL

New

Mounting struts No.12 for CarMotion, 12 pcs

IN STOCK

Mounting supports for building roads from I-Track CarMotion segments are available in lengths from 27–197 mm (No. 1–18, each set contains 12 pieces of the same size) in 10 mm increments. A complete set, cat. no. HCT9452-20, is also available, containing supports No. 1–18 with 2 pieces each. The set includes all components required for installation on the baseboard, including screws. The supports are designed for precise adjustment of gradient and height when building roads in the CarMotion system. The design allows easy installation and flexible route configuration.

9,29€

DETAIL

New

FLEXI transition pieces 1.85/2,85 × 10 cm 12 pcs

IN STOCK

Transition piece. For curves with a radius of less than 20 cm, use the FLEXI transition piece HCT9402T and continue with FLEXI segments 2,85 cm HCT9402F. This increases the spacing of the guide magnetic strips to 1 cm, allowing longer vehicles and buses to pass each other safely in curves. At the end of the curve, use the same transition piece again to return to the standard spacing of the guide magnetic strips of 4 cm on straight sections.

6,95€

DETAIL

VIESSMANN Car Motion Accessories