NEWS | www.hacker-model.com

New

Receiver coil for retrofitting trucks and buses

check availability

The receiver coil adds inductive charging and the necessary communication capabilities to vehicles. It simply clips onto the transmission block and connects to the vehicle's circuit board via a two-pin connector. Combined with the Inductive Charger (item 8408), it enables unlimited driving time without user intervention. Vehicles can be switched on and off at inductive charging stations. The driving time-to-charging time ratio is approximately 3:1, depending on the system and vehicle conditions. Suitable for all CarMotion system vehicles without built-in receiver coils. External dimensions: L 2.4 x W 1.3 x H 0.27 cm

10,75€

DETAIL

New

Universal electronics truck

check availability

The Universal Electronics Truck offers compact solutions for retrofitting trucks (over 7.5 t) with the proven driving characteristics of CarMotion trucks. The slim module (W 12.5 mm x L 26.5 mm) is particularly suitable for tight installation situations and works in conjunction with the H0 gearbox with motor (item no. 8426). Power is supplied by two 60 mAh batteries included in the set. The module is intended exclusively for this motor and batteries. An additional, shortenable distribution board (approx. W 7 mm x L 25 mm; shortenable to L 17 mm) facilitates the connection of LEDs for lighting tasks and enables additional lighting effects. An expansion interface for additional modules is available. The LEDs and sensors are already provided with enameled wires to ensure easy installation. Additional sets for additional lighting effects will be available in the future. The set includes: main board, distribution board, hall sensor, charging and programming socket, 2 batteries, rear bumper

102,42€

DETAIL

New

H0 Set of rubber tires, 10 pieces

IN STOCK

This set allows you to equip your CarMotion trucks if the original tires are damaged or worn out. The tires are characterized by good traction, smooth running, and directional stability, and can also be used for truck trailers.

9,75€

DETAIL

New

H0 retrofit kit steered rear axles for semi-traile

check availability

These steered axles for semi-trailers are ideal for driving even with longer trailers on tighter radii, without having to widen the road significantly in curves or causing the trailers to stray too far into the lane of oncoming traffic. Precisely guided by a ball-bearing gear-ring mechanism.

44,58€

DETAIL

New

H0 Retrofit Kit Rubber Tires for Kibri Trailers an

IN STOCK

Product Information "H0 Retrofit Kit Rubber Tires for Kibri Trailers and Semi-Trailers, Twin Tires" This kit allows you to retrofit your Kibri trailers or semi-trailers to optimize the smooth running and tracking of the vehicle. This improves the handling characteristics of the trailer or semi-trailer. Contents: 8 rubber tires, 4 rims, 2 steel axles, 4 bushings. Suitable for 2-axle trailers and semi-trailers with twin tires.

25,83€

DETAIL

New

Charger for trucks and buses

IN STOCK

The charger for trucks and buses in the Viessmann CarMotion system can be powered by any standard USB power adapter or virtually any device such as a PC, laptop, power bank, etc. The charger can be connected to a USB-A power source using the included cable. The charger plug is simply inserted into the designated socket under the CarMotion vehicle. An empty battery is charged in approximately 35 minutes, and a partially discharged battery is charged correspondingly faster. The current charging status of the vehicle is indicated during charging by the vehicle's interior lighting flashing in four different levels.

26,79€

DETAIL

New

Inductive Charger

check availability

The InductiveCharger enables wireless vehicle recharging and inductive communication with the vehicle. Vehicles stop on the module and automatically position themselves over the charging coil, with charging currents being automatically adjusted. These modules are particularly suitable for locations with longer stop times, such as traffic lights, railroad crossings, or gas stations. Multiple modules can be networked with future software updates to autonomously guide vehicles to charging positions. A control output for the motorized 2/3-way junction (item 8448), which can also control servos, rounds out the capabilities. For trucks, the ratio of travel time to charging time is approximately 3:1. This allows for virtually unlimited travel time. The InductiveCharger can also switch vehicles with receiver coils on and off. The vehicles must be retrofitted with the receiver coil (item 8440). Charging coil diameter: 40 mm, electronics diameter: 30 mm, height: 60 mm

137,29€

DETAIL

New

Permanent magnet holder for test operation, 2 piec

check availability

The permanent magnet mount is the ideal solution for testing the CarMotion system. Equipped with one or more magnets, the mount can be flexibly positioned to the right of the road. This allows you to specifically test whether and where the CarMotion vehicle recognizes and implements defined control commands. The robust design allows for quick setup and easy repositioning during test runs – for precise results under realistic conditions.The permanent magnet mount is the ideal solution for testing the CarMotion system. Equipped with one or more magnets, the mount can be flexibly positioned to the right of the road. This allows you to specifically test whether and where the CarMotion vehicle recognizes and implements defined control commands. The robust design allows for quick setup and easy repositioning during test runs – for precise results under realistic conditions.

6,67€

DETAIL

New

8230 H0 MB ACTROS 2-axle concrete mixer trailer

IN STOCK

This practical accessory set contains a remote control, 10 meters of magnetic tape (0.5 mm), 10 permanent magnets, a charger and a programming device.

102,96€

DETAIL

New

IR remote control

IN STOCK

The remote control allows for easy control of the CarMotion vehicles on the system, as well as simple adjustments to the vehicle. To do this, the remote control is pointed at the front of the vehicle, where its infrared sensors are located. Distances greater than approximately 50 cm from the vehicle require more precise alignment of the remote control; up to 1 m is possible under favorable conditions. It is therefore suitable for locally influencing vehicles – driving by sight, so to speak. A vehicle can be started with it – even by an active stop coil – and stopped at any time. Furthermore, the vehicle speed and existing functions on the vehicle – such as the lights, indicators, etc. – can be adjusted. This means that the vehicle does not need to be connected to the programming device for these basic configurations. The remote control also supplements the control of the vehicles via the magnet arrangements under the roadway – enabling complex processes with additional options for user

17,38€

DETAIL

New

H0 CarMotion Basic Starter Set, MB Round-Cab 3-axl

IN STOCK

CarMotion Basic Starter Set consisting of Item 8020, H0 MB round-cab 3-axle dump truck (base), 1 charger with USB cable (Item 8400), 12 permanent magnets (Item 8431), and 1 magnetic pin. Matching sound retrofit kit: Item 8454

275,58€

DETAIL

New

H0 Retrofit Kit Rubber Tires for Kibri Trailers an

IN STOCK

Product Information "H0 Retrofit Set Rubber Tires for Kibri Trailers and Semi-Trailers, Single Tires" This set allows you to retrofit your Kibri trailers or semi-trailers to optimize the smooth running and tracking of the vehicle. This improves the handling characteristics of the trailer or semi-trailer. Contents: 6 rubber tires, 6 rims, 3 steel axles, 6 bushings. Suitable for trailers and semi-trailers with up to 3 axles and single tires.

22,96€

DETAIL