NEWS | www.hacker-model.com

New

IN STOCK

Base plate 6 cm. The board has a special construction that guarantees rigidity and very low weight. The reinforcing bars have openings at the top that can be used for cable installation. Holes in the bottom plate provide access to all locations.

60,50€

DETAIL

New

Tabletop Model Railway Start board 110x80x10 cm

IN STOCK

Starter board for the I-Track tabletop model railway. It is delivered fully assembled, allowing you to immediately start laying tracks or building roads for CarMotion. Tracks from a starter set can be easily assembled on the board, so you can begin operation right away. After use, simply remove the locomotive and cars and store the board with the tracks safely in the supplied box. If you wish to leave the board on the table, simply place the supplied spacers in the corners and put the lid on top. This creates a safe clearance of 8 cm above the layout for locomotives and cars. Openings in the sides and bottom ensure easy access. Multiple starter boards can be connected side by side using M8 bolts with wing nuts (order number HCT8460S4), creating a large modular layout.

138,08€

DETAIL

New

FLEXI transition pieces 1.35/1,85 × 10 cm 12 pcs

IN STOCK

Transition piece. For curves with a radius of less than 20 cm, use the FLEXI transition piece HCT9403T and continue with FLEXI segments 2,85 cm HCT9402F. This increases the spacing of the guide magnetic strips to 1 cm, allowing longer vehicles and buses to pass each other safely in curves. At the end of the curve, use the same transition piece again to return to the standard spacing of the guide magnetic strips of 4 cm on straight sections.

5,90€

DETAIL

New

Street bedding FLEX element CarMotion 1,35 cm

IN STOCK

Street bedding Flex element for the installation of the magnetic strip, 1 mm. Base for the flexible construction of single- or dual-lane road sections (straight and curved).

14,90€

DETAIL

New

Street bedding Straight element CarMotion 1,35 cm

IN STOCK

Street bedding Straight element for the installation of the magnetic strip, 1 mm. Base for the construction of Straight single- or dual-lane road sections.

11,90€

DETAIL

New

FLEXI transition pieces 1.85/3.35 × 10 cm 12 pcs

IN STOCK

Transition piece. For curves with a radius of less than 20 cm, use the FLEXI transition piece HCT9404T and continue with FLEXI segments 3.35 cm HCT9404F. This increases the spacing of the guide magnetic strips to 1.5 cm, allowing longer vehicles and buses to pass each other safely in curves. At the end of the curve, use the same transition piece again to return to the standard spacing of the guide magnetic strips of 4 cm on straight sections.

6,95€

DETAIL

New

Street bedding FLEX element CarMotion 3,35 cm

IN STOCK

Street bedding Flex element for the installation of the magnetic strip, 1 mm. Base for the flexible construction of single- or dual-lane road sections (straight and curved).

14,90€

DETAIL

New

FLEXI transition pieces 1.85/2,85 × 10 cm 12 pcs

IN STOCK

Transition piece. For curves with a radius of less than 20 cm, use the FLEXI transition piece HCT9402T and continue with FLEXI segments 2,85 cm HCT9402F. This increases the spacing of the guide magnetic strips to 1 cm, allowing longer vehicles and buses to pass each other safely in curves. At the end of the curve, use the same transition piece again to return to the standard spacing of the guide magnetic strips of 4 cm on straight sections.

6,95€

DETAIL

New

Road bedding plates 60° intersection Left

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

7,33€

DETAIL

New

Reduction between diameters of 21 and 22.5 cm

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

5,33€

DETAIL

New

Street bedding curved element 60° for CarMotion

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

12,58€

DETAIL

New

Street bedding curved element 45° for CarMotion

IN STOCK

I-Track roadbed plates for the Car Motion System – including crossing, curve, and straight plates. The street and crossing roadbed plates of the I-Track roadbed system are made of a special 1 mm material and are glued directly onto the base surface – either with traditional wood glue or with Hacker’s industrial CA superglue. The roadbed plates are factory-prepared with perfectly and precisely pre-cut grooves for installing the 3×1 mm Viessmann magnetic strip (item no. V8430). The crossing roadbed plates additionally feature pre-cut openings for mounting the mechanical Viessmann turnouts (item no. V8448 or V8445). This makes installing the magnetic strip extremely easy. At the turnout position, simply drill a 35 mm hole into the baseboard using a step drill. The mechanical turnout is then mounted on the underside of the baseboard using the I-Track Holder W (item no. HCT8408W).

11,96€

DETAIL